Click Here to learn how to vent a hip roof

SmartVent by DCI has received an evaluation approval from the Intenational Code Council, Approved by the Texas department of Insurance and passed a wide array of field and lab testing

SmartVent can be use at the eave, mid-roof, shed-wall, off-peak and dormers

SmartVent has an App for that!
Click the application you need!

Need directions for SmartVent and the SmartVent End Caps? Use the links below

SmartVent may actually extend the life of your asphalt shingles because of the maximum intake it provides to an attic, thus a better breathing roof is a healthier roof.

You may also see a reduction in utility expenses. SmartVent keeps your attic cooler in the warm months and reduces the load needed to air-condition your home.

What is SmartVent?

SmartVent is a tapered, under shingle plastic product designed for installation along the soffit edge of the roof or the facing edge of dormer rakes and goes virtually unnoticed. It allows air to flow freely through the 1" roof decking slit providing more than adequate soffit ventilation to maximize ridge vent effectiveness. This is extremely important since most ridge vent products require an equal amount of ventilation at the soffit in order to work properly. SmartVent, when used at both soffits, has a total NFA rating of 18 sq. in. (or 9 sq. in. on each side of a standard gable roof).

SmartVent is a patented roof and attic ventilation product that provides the best passive attic ventilation available. Using a unique design and installation method, SmartVent eliminates the problems and inefficiencies found in roof construction using ridge and soffit venting, namely inadequate vent openings in the soffit.

Read the Testimonials......

Contact Your Local Distributor for Pricing and Availability

What is a SmartVent End Cap?

SmartVent End Caps are 10.5" square tapered ventilation pieces that seamlessly blend with Smartvent to give the roof a more aesthetic and clean finish to your intake ventilation project. (Do not use SmartVent End Caps at the rake edges)

The New, Patent-Pending 'Universal' SmartVent End Cap can be installed Right Side or Left Side, as you begin your SmartVent run or end the run. Designed with the contractor in mind, this easy to install end cap makes working with SmartVent simple and cost effective. Use it to end a SmartVent run near a dormer, valley, hip, chimney or skylight. Use it to begin a SmartVent run other than at the rake edge. At the rake edge, wrap SmartVent fabric around a full piece of SmartVent as shown in the SmartVent directions.

The SmartVent End Cap 'tapers' the SmartVent back down to the roof. All that you need to do is nail it down to the roof. Period! The fabric is already attached at the factory for right hand or left hand installations.

Refer to the technical drawing - click to enlarge details.

SmartVent attic ventilation is virtually invisible on the roof. Click on the images below to see how your house could look.

SmartVent is rated at 9 NFA. SmartVent also satisfies all ridge vent and exhaust vent requirements. Patent numbers 6,212,833 & 6,447,392 issued by the United States Patent & Trademark Office.

“We have been using SmartVent for years as a great solution for inadequate ventilation on our customer’s homes. Not only does the SmartVent perform great, it installs easier than any of the competitor’s products!”

Wayne Watkins
Brother’s Roofing
Baltimore, MD

Do you have a question about SmartVent?
Look Through Our NEW FAQ (Frequently Asked Questions) Section By clicking on this text.

SmartVent Eave

Click here for SmartVent Specifications

Most houses with ridge vents do not have the proper soffit ventilation required because attic insulation blocks the soffit vents. SmartVent allows cooler air to enter under the shingle, through the 1" roof slit and out the ridge vent providing superior air flow and attic cooling.

Click here for an expanding list of SmartVent Dealers. If no dealer is located near you please give us a call at 1-800-622-4455 and we will be happy to locate a dealer for you.

Roofing Contractor magazine is featuring DCI's product line in "Ventilating Problem Areas"
Article written by Chris King, editor of RC magazine.
Click here or on the image above to read the article